Throwback Thursday 19 CN at Rymal Part II
on Wednesday, July 5, 2017
Tonight's Throwback Thursday features the second half of my Dad Keith's write-up of the namesake location for this blog. Thanks again Dad!
- Peter.
As mentioned in the previous Rymal anecdote, the former Hamilton and Northwestern Railway line would cling to life into the early 1990’s, finally succumbing to abandonment in 1993. However, the line did not vanish without a final blaze of glory!
Towards the end, the lightly-traversed branchline was a bastion of venerable CNR road power, including the long serving mainstay GMD SW1200’s, GMD GP9’s as well as the occasional MLW RS-18. However, as shown above, the most noteworthy and beloved units by far were the handful of CN’s infamous remaining snow service GMD F7’s. With no on-route switching demands, the F7 A/B consists were ideally suited to the inter-plant traffic pattern requirements of ‘The Steel Company of Canada’, aka ‘Stelco’, transporting continuously-cast slabs from their newer flagship facility in Nanticoke to the rolling mills located at Hilton Works, situated on the Hamilton waterfront. For an all-too-brief period, pure A-B-A sets as shown, and on occasion F7’s mixed with GP9’s ferried 60 ft flatcars, equipped with specialized slab cradles, from lakefront (actually Hamilton Harbour/Lake Ontario) to lakefront (Lake Erie). While more than a delight for the local railfan community (See ‘F Units on the Nanticoke/CN 9100’s produced by Green Frog Productions, www.greenfrog.comshot by area enthusiast Rob McCormack), some operational concerns were voiced. Lower city dwellers became increasingly concerned about the potential for a loaded runaway slab train descending the escarpment without brakes, careening through their community. This, despite the fact that the line had crested the geographical outcrop in the mid 1870’s and had been disaster free for well over a century! As the unlikely catastrophe dialogue was heating up, the matter was resolved by an unforeseen event when the bridge over Stone Church Road (located approximately under the trailing caboose) was displaced by an over-height transport truck – see photo below. Owing to the compromised structural integrity of the span, rail traffic was suspended south from CN’s Stuart St. yard (the alternative, much more circuitous routing, involved movement from Stuart St. yard to Brantford along the Dundas sub, then back to Caledonia to rejoin the former H&NW line). As if to add an exclamation point, the span was displaced in the opposite direction, shortly thereafter, by another unfortunate truck encounter. This time the injured bridge span was lifted and placed perpendicular on the right of way! As previously mentioned, much of the H&NW chartered line remains as the ‘STONE CHURCH ROAD RAIL TRAIL’. North of Stone Church Road the former right of way is known as the ‘ESCARPMENT RAIL TRAIL’. One can walk or ride their bike past them, but no longer does the sound of normally-aspirated 567's echo off the concrete silo walls...
- Keith.
 |
Above: Atop the escarpment, as shown, the H&NW chartered line descended to the first station stop at Rymal. No doubt longer freight trains would have been a challenge for the hogger with part of his consist ascending and part descending at the same time! For additional information on the ‘Hamilton and Northwestern Railway’ refer to Charles Cooper’s superb manuscript entitled ‘RAILS TO THE LAKES’. Reportedly, creating the path to climb from the lower city was accomplished by Irish labourers ("navvies", displaced canal builders) over a three year period at a cost of approximately one million 1870’s dollars! A modern day remnant of their efforts is the downtown ‘Cork Town’ community, so named on account of their off duty shenanigans! Apparently construction of Hamilton’s first jails more or less accompanied the building of the H&NW! |
 |
| Above: Late local area business development did generate a limited amount of additional activity on the line. Shown on the below are CN 603042 and DWC 605628, Canadian-built 52’-8” bulkhead flatcars (see the October 1990 issue of Railroad Model Craftsman Magazine for drawings and additional background) on the Rymal siding. The duo is loaded with drywall for ‘Ferrell Builders Supply’ an area materials provider. The concrete grain silo structure in the foreground is believed to have been constructed just prior to World War II, several years ahead of the adjacent CO-OP installation. The silo complex was built by the owner of the neighbouring Binbrook Feed Mill operation. Storage space was also leased to other enterprises, including the nearby Hannon Feed Mill. Operation of the silo complex would have most likely continued into the mid 1960’s, just prior to the widespread use of large volume covered hopper cars for grain transport. The low volume operation was set up for boxcar grain delivery. Undoubtedly, the improved highway system and truck transport rendered the facility redundant to local area needs. Incredibly, the concrete structure is still sound with the interior mostly preserved - the vertical wooden bucket elevator and much of the original woodwork are still solidly in place. It’s like the owner just walked away one day! |
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment